First step into controlled chromatography
You routinely purify your samples on an open glass column and have to cope with a limited resolution and a long separation time. As a first step toward automation, we offer a small system allowing to control the flow rate and the eluent composition. The «Preparative Chromatography Easy» purification system addresses the requirements specific to the isolation of compounds from a synthesis mixture.
Improved separation
• Fine-tuned separation efficiency using gradient elution
• Controlled separation optimization with precise monitoring of the eluent composition
• Increased purity of the collected fractions with a higher resolution of the separation
Time and money saving
• Reduced elution time from hours to minutes with controlled flow rate and solvent composition allowing to reduce the fraction volumes for a faster evaporation.
• Decreased purification cost with lower solvent consumption
• Low initial investment with upgrade possibilities
Easy and safe
• Intuitive control of pumping parameters: no training required
• Minimized solvent exposure
| | |
Model | Sepacore® “Easy” purification systems |
| | |
Pump C-601 / C-605 | | |
Gradient | Binary |
Pump type | Radially arranged 3 – piston pump |
Pump head | Integrated piston back flushing |
Function | 3 – piston pump chemically inert and biocompatible |
Material in contact with solvent | PEEK, sapphire, ceramic, FEP, ruby |
Interface | 4 x RS485 |
Connection voltage | 100 – 230 V ± 15 % |
Frequency | 50 / 60 Hz |
Power consumption | max. 75 W |
Degree for protection | IP20 |
Overvoltage category | II |
Pollution degree | 2 |
Pressure range | 0 – 10 bar or 0 – 50 bar |
Flow rate | 2.5 mL/min – 250 mL/min |
Flow rate accuracy | +/- 2 % of the set flow rate, calibration option for specific solvents and temperatures |
Reproducibility | +/- 0.5 % of the set flow rate |
Environmental conditions |
Temperature | 5 – 35 °C for indoor use only |
Altitude | up to 2000 m |
Humidity | maximum relative humidity 80 % for temperature up to 31 °C, and then lineary decreasing to 50 % at 40 °C |
| | |
Pump manager C-615 | |
Connection voltage | 24 V DC |
Interfaces | | |
| 1 × RS232 (process data output) |
| 1 × Mini DIN (TTL in/out for alarm supervision and/or extern. start) |
| 1 × Mini DIN (pressure sensor) |
| 2 × Mini DIN (optional level sensor) |
| 2 × Mini DIN (solvent valves) |
Gradient function | from 0 % – 100 % B for total flow rate of 2.5 – 250 mL, linearity ± 2 % |
Display | LCD display, 128 x 64 pixels (58 x 29 mm) |
Dialog languages | en / de / sp / fr / it / jp / cn |
| | |
Sepacore® “Easy” purification systems Technical data sheet
Sepacore® «Easy Synthesis» and «Easy Extract» purification systems are designed for gradient separations up to 10 bar (145 psi) or 50 bar (725 psi). They enable a fast operation and easy programming. A large graphical display allows a quick and easy set up. It fits perfectly for plastic cartridges or glass columns for product amounts up to several hundred grams.
Sepacore® Easy Purification Systems (брошюра)
Первый шаг к автоматической хроматографии
ростота и безопасность нтуитивно понятное управление и минимальное воздействие растворителя
Вы регулярно очищаете образцы на открытых стеклянных колонках и в условиях задачи есть ограничения по разрешению и длительности разделения. В качестве первого шага на пути к автоматизированному процессу мы предлагаем две компактные системы S и r позволяющие контролировать расход и состав элюента.
Sepacore Easy Purification Systems (brochure)
Sepacore Easy Purification Systems
Preparative_Chromatography_Solution_brochure_ru_A_01.pdf
To get information about: «Preparative Chromatography Easy» contact us by phone (044) 229 15 31 or fill in the form.